Numerical investigation on role of a circular deflector with diagonal splitter blades on performance of savonius turbine

Document Type : Original Article

Authors

1 MSc student, Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran.

2 Professor, Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran.

Abstract
One of the most important sources of renewable energy is wind energy. We can harness the kinetic energy of the wind by using wind turbines. One of the fundamental problems with Savonius wind turbines is their low efficiency due to direct wind impact on the returning blade and applying negative torque to it. One new and cost-effective method to increase the efficiency of these turbines is to use a deflector upstream of the flow to prevent wind from hitting the returning blade and producing negative torque. Due to the cylindrical geometry of the deflector, it cannot guide the flow at an arbitrary angle. Additionally, a relatively large vortex region will form downstream of the deflector and near the turbine, which will have undesirable effects on turbine performance. These vortices can be controlled by installing flow splitter blades on the deflector. This study used computational fluid dynamics techniques in a two-dimensional simulation with Ansys Fluent software. Initially, a cylindrical deflector without flow splitter blades was designed and its simulation results were validated with previous experimental research. Then, as an innovation, a splitter blade was installed at a desired angle and directed flow towards the advancing blade of the turbine. The simulation results show that using a deflector with splitter blades at an angle of 5 degrees increases the turbine power coefficient by 23.4% compared to its state without a deflector at a tip speed ratio of 0.6.

Keywords

Subjects


- مراجع
[1]   N. L. Panwar, S. C. Kaushik and S. Kothari, Role of renewable energy sources in environmental protection: A review, Renewable and Sustainable Energy Reviews, Vol. 15, No. 3, pp. 1513-1524, 2011.
[2]  S. E. Hosseini, An outlook on the global development of renewable and sustainable energy at the time of COVID-19, Energy Research & Social Science, Vol. 68, pp. 101633, 2020.
[3] Q. A. Alabdali, A. M. Bajawi, A. M. Fatani and A. M. Nahhas, Review of Recent Advances of Wind Energy, Energy, Vol. 8, No. 1, pp. 12-19, 2020.
[4]  P. Gipe and E. Möllerström, An overview of the history of wind turbine development: Part I—The early wind turbines until the 1960s, Wind Engineering, Vol. 46, No. 6, pp. 1973-2004, 2022.
[5]  S. Toudarbari, M. J. Maghrebi and A. Hashemzadeh, Evaluation of Darrieus wind turbine for different highway settings using CFD simulation, Sustainable Energy Technologies and Assessments, Vol. 45,pp.101077,2021.
[6]  M. H. Mohamed, F. Alqurashi and D. Thévenin, Performance enhancement of a Savonius turbine under effect of frontal guiding plates, Energy Reports, Vol. 7, pp. 6069-6076, 2021.
[7]  A. Roshan, A. Sagharichi and M. J. Maghrebi, Nondimensional parameters’ effects on hybrid Darrieus–Savonius wind turbine performance, Journal of Energy Resources Technology, Vol. 142, No. 1, 2020.
[8]  N. R. Maldar, C. Y. Ng and E. Oguz, A review of the optimization studies for Savonius turbine considering hydrokinetic applications, Energy Conversion and Management, Vol. 226, pp. 113495, 2020.
[9]  M. Mohamed, G. Janiga, E. Pap and D. Thévenin, Optimization of Savonius turbines using an obstacle shielding the returning blade, Renewable Energy, Vol. 35, No. 11, pp. 2618-2626, 2010.
[10] P. A. Setiawan, T. Yuwono, W. A. Widodo, E. Julianto and M. Santoso, Numerical study of a circular cylinder effect on the vertical axis Savonius water turbine performance at the side of the advancing blade with horizontal distance variations, International Journal of Renewable Energy Research, Vol. 9, No. 2, pp. 978-985, 2019.
[11] E. Nimvari, H. Fatahian and E. Fatahian, Performance improvement of a Savonius vertical axis wind turbine using a porous deflector, Energy Conversion and Management, Vol. 220, pp. 113062, 2020.
[12] K. Layeghmand, N. Ghiasi Tabari and M. Zarkesh, Improving efficiency of Savonius wind turbine by means of an airfoil-shaped deflector, Journal of the Brazilian Society of Mechanical Sciences and Engineering, Vol. 42, No. 10, pp. 528, 2020.
[13]         T. Yuwono, G. Sakti, F. Nur Aulia and A. Chandra Wijaya, Improving the performance of Savonius wind turbine by installation 
of a circular cylinder upstream of returning turbine blade, Alexandria Engineering Journal, Vol. 59, No. 6, pp. 4923-4932, 2020.
[14] W. Tian, J. Bian, G. Yang, X. Ni and Z. Mao, Influence of a passive upstream deflector on the performance of the Savonius wind turbine, Energy Reports, Vol. 8, pp. 7488-7499, 2022.
[15] B. D. Altan and A. Gungor, Examination of the Effect of Triangular Plate on the Performances of Reverse Rotating Dual Savonius Wind Turbines, Processes, Vol. 10, No. 11, pp. 2278, 2022.
[16] E. Fatahian, F. Ismail, M. H. H. Ishak and W. S. Chang, The role of wake splitter deflector on performance enhancement of Savonius wind turbine, Physics of Fluids, Vol. 34, No. 9, pp. 095111, 2022.
[17] W. Xu, C.-c. Li, S.-x. Huang and Y. Wang, Aerodynamic performance improvement analysis of Savonius vertical axis wind turbine utilizing plasma excitation flow control, Energy, Vol. 239, pp. 122133, 2022.
[18] I. Marinić-Kragić, D. Vučina and Z. Milas, Robust optimization of Savonius-type wind turbine deflector blades considering wind direction sensitivity and production material decrease, Renewable Energy, Vol. 192, pp. 150-163, 2022.
[19] H. Aboujaoude, F. Beaumont, S. Murer, G. Polidori and F. Bogard, Aerodynamic performance enhancement of a Savonius wind turbine using an axisymmetric deflector, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 220, pp. 104882, 2022.
[20] R. E. Sheldahl, B. F. Blackwell and L. V. Feltz, Wind tunnel performance data for two-and three-bucket Savonius rotors, Journal of Energy, Vol. 2, No. 3, pp. 160-164, 1978.
 

  • Receive Date 10 June 2023
  • Revise Date 15 May 2024
  • Accept Date 19 August 2024