Journal of Renewable and New Energy

Investigating the crisis of energy consumption in residential-commercial buildings and presenting a new solution using phase change materials nanocomposites

Document Type : Review Article

Authors

Fariba Mohammadi 1
Zahra Saeid 1
Maryam Behzadi 1
Hamideh Mahdavi 1
Negin Vahidinia 1
Aziz Babapoor 2

1 Master's student, Chemical Engineering, Faculty of Engineering, Mohaghegh Ardabili University, Ardabil

2 Associate Professor, Department of Chemical Engineering, University of Mohaghegh Ardabili, Ardabil, Iran

https://doi.org/10.22034/jrenew.2024.200150
Abstract
In this research, phase change materials (PCMs) have been examined as innovative tools for temperature control in thermal systems. These materials, operating intelligently without the need for mechanical equipment, undergo phase transitions naturally, adapting to environmental fluctuations and thereby enhancing energy efficiency in thermal systems. The study delves into the investigation and classification of the characteristics of these materials, along with their applications in various building components such as walls, windows, bricks, artificial stones, ceilings, and floors. The obtained results from the use of these materials indicate their potential as a novel solution for optimizing energy consumption in buildings. For instance, incorporating PCMs in walls leads to a reduction in thermal energy consumption, and utilizing nano-insulation in windows decreases the need for heating and cooling systems, providing users with greater independence from these facilities. Furthermore, the effect of PCMs in stones contributes to thermal stability, and in bricks, it significantly diminishes greenhouse gas emissions. Overall, the integration of PCMs in building floors enhances thermal storage capacity. These findings underscore the practical utility of PCM as an effective solution for improving the energy efficiency of buildings.

Keywords

Phase change material
Building
wall
Window
Roof
Floor
Tube

Subjects

7- مراجع

[1]  M. Salihi, M. El Fiti, Y. Harmen, Y. Chhiti, A. Chebak, F. E. M. h. Alaoui, M. Achak, F. Bentiss, C. Jama, Evaluation of global energy performance of building walls integrating PCM: Numerical study in semi-arid climate in Morocco, Case Studies in Construction Materials, Vol. 16, pp. e00979, 2022.
[2]  Q. Al-Yasiri and M. Szabó, Experimental study of PCM-enhanced building envelope towards energy-saving and decarbonisation in a severe hot climate, Energy and Buildings, Vol. 279, p. 112680, 2023.
[3]  B. Alshuraiaan, Efficient utilization of PCM in building envelope in a hot environment condition, International Journal of Thermofluids, Vol. 16, pp. 100205, 2022.
[4]  A. Haghighi, A. Babapoor, M. Azizi, Z. Javanshir, and H. Ghasemzade, Optimization of the thermal performance of PCM nanocomposites, Journal of Energy Management and Technology, Vol. 4, No. 2, pp. 14-19, 2020.
[5]  P. K. S. Rathore and S. K. Shukla, Potential of macroencapsulated PCM for thermal energy storage in buildings: A comprehensive review, Construction and Building Materials, Vol. 225, pp. 723-744, 2019.
[6]  C. K. Oluah, E. T. Akinlabi, and H. O. Njoku, CFD study on the thermal performance of n-Octadecane (PCM) doped with graphene nanoparticles as a potential thermal energy storage medium for trombe walls, in Advances in Manufacturing Engineering: Selected articles from ICMMPE 2019, pp. 539-553, 2020.
[7]  A. Babapoor, M. AhmadiMezjin, A. Hoseinasadi, S. Jokar, M. Paar, and S. Golestaneh, Simulation and Optimization of Thermal Management in L-Shaped Tubes Coated with Phase Change Material Nanofibers, Iranian Chemical Engineering Journal, Vol. 18, No. 107, pp. 15-27, 2020.
[8]  C. V. Podara, I. A. Kartsonakis, and C. A. Charitidis, Towards phase change materials for thermal energy storage: classification, improvements and applications in the building sector, applied sciences, Vol. 11, No. 4, p. 1490, 2021.
[9]  D. Lencer, M. Salinga, B. Grabowski, T. Hickel, J. Neugebauer, and M. Wuttig, A map for phase-change materials, Nature materials, Vol. 7, No. 12, pp. 972-977, 2008.
[10] M. Saffari, A. De Gracia, C. Fernández, and L. F. Cabeza, "Simulation-based optimization of PCM melting temperature to improve the energy performance in buildings," Applied Energy, Vol. 202, pp. 420-434, 2017.
[11] X. Jin, S. Zhang, X. Xu, and X. Zhang, Effects of PCM state on its phase change performance and the thermal performance of building walls, Building and Environment, Vol. 81, pp. 334-339, 2014.
[12] A. Babapoor, Z. Dehghan Khaje Bolagh, M. Ganjkhani, and M. Paar, "An Insight into the Energy Optimization in New Generation Clothes Using Phase Change Materials, Journal of Renewable and New Energy, Vol. 8, No. 1, pp. 70-77, 2021. (in Persian)
[13] F. Nahidi Azar, S. Karimi, Examining the achievements of nanocomposite in the construction industry, in International Conference on Modern Research in Civil Engineering, Architectural & Urban development,: Berlin, 2016.
[14] M. Sen, Nanocomposite materials, Nanotechnology and the Environment, pp. 1-12, 2020.
[15] V. Butala and U. Stritih, Experimental investigation of PCM cold storage, Energy and Buildings, Vol. 41, No. 3, pp. 354-359, 2009.
[16] E. M. Alawadhi, Thermal analysis of a building brick containing phase change material, Energy and Buildings, Vol. 40, No. 3, pp. 351-357, 2008.
[17] D. Zhou, C.-Y. Zhao, and Y. Tian, Review on thermal energy storage with phase change materials (PCMs) in building applications, Applied energy, Vol. 92, pp. 593-605, 2012.
[18] G. Zhou, Y. Yang, X. Wang, and J. Cheng, Thermal characteristics of shape-stabilized phase change material wallboard with periodical outside temperature waves, Applied Energy, Vol. 87, No. 8, pp. 2666-2672, 2010.
[19] D. Hawes and D. Feldman, Absorption of phase change materials in concrete, Solar Energy Materials and Solar Cells, Vol. 27, No. 2, pp. 91-101, 1992.
[20] L. F. Cabeza, C. Castellon, M. Nogues, M. Medrano, R. Leppers, and O. Zubillaga, Use of microencapsulated PCM in concrete walls for energy savings, Energy and buildings, Vol. 39, No. 2, pp. 113-119, 2007.
[21] S. Shrestha, W. Miller, T. Stovall, A. Desjarlais, K. Childs, W. Porter, M. Bhandari, S. Coley, Modeling PCM-enhanced insulation system and benchmarking EnergyPlus against controlled field data, in Proceedings of building simulation, 2011, pp. 800-807.
[22] K. W. Childs and T. K. Stovall, Use of phase change material in a building wall assembly: a case study of technical potential in two climates, 2012.
[23] S. N. Al-Saadi and Z. J. Zhai, Modeling phase change materials embedded in building enclosure: A review, Renewable and Sustainable Energy Reviews, Vol. 21, pp. 659-673, 2013.
[24] F. Kuznik and J. Virgone, Experimental investigation of wallboard containing phase change material: Data for validation of numerical modeling, Energy and Buildings, Vol. 41, No. 5, pp. 561-570, 2009.
[25] W. He, C. Yu, J. Yang, B. Yu, Z. Hu, D. Shen, X. Liu, M. Qin, H. Chen, Experimental study on the performance of a novel RC-PCM-wall, Energy and Buildings, Vol. 199, pp. 297-310, 2019.
[26] A. Kasaeian, F. Pourfayaz, E. Khodabandeh, and W.-M. Yan, Experimental studies on the applications of PCMs and nano-PCMs in buildings: A critical review, Energy and Buildings, Vol. 154, pp. 96-112, 2017.
[27] X. Zhang, R. Wen, C. Tang, B. Wu, Z. Huang, X. Min, Y. Huang, Y. Liu, M. Fang, X. Wu, Thermal conductivity enhancement of polyethylene glycol/expanded perlite with carbon layer for heat storage application, Energy and Buildings, Vol. 130, pp. 113-121, 2016.
[28] P. Arce, C. Castellón, A. Castell, and L. F. Cabeza, Use of microencapsulated PCM in buildings and the effect of adding awnings, Energy and Buildings, Vol. 44, pp. 88-93, 2012.
[29] X. Kong, S. Lu, J. Huang, Z. Cai, and S. Wei, Experimental research on the use of phase change materials in perforated brick rooms for cooling storage, Energy and buildings, Vol. 62, pp. 597-604, 2013.
[30] Q. Xing, X. Hao, Y. Lin, H. Tan, and K. Yang, Experimental investigation on the thermal performance of a vertical greening system with green roof in wet and cold climates during winter, Energy and Buildings, Vol. 183, pp. 105-117, 2019.
[31] W. He, C. Yu, J. Yang, B. Yu, Z. Hu, D. Shen, X. Liu, M. Qin, H. Chen, Experimental study on the performance of a novel RC-PCM-wall, Energy and Buildings, Vol. 199, pp. 297-310, 2019.
[32] M. Hu, G. Pei, Q. Wang, J. Li, Y. Wang, and J. Ji, Field test and preliminary analysis of a combined diurnal solar heating and nocturnal radiative cooling system, Applied energy, Vol. 179, pp. 899-908, 2016.
[33] R. Barzin, J. J. Chen, B. R. Young, and M. Farid, Application of PCM energy storage in combination with night ventilation for space cooling, in Thermal Energy Storage with Phase Change Materials, ed: CRC Press, 2021, pp. 259-276.
[34] F. Fiorito, Trombe walls for lightweight buildings in temperate and hot climates. Exploring the use of phase-change materials for performances improvement, Energy Procedia, Vol. 30, pp. 1110-1119, 2012.
[35] F. Ye, Z. Ge, Y. Ding, and J. Yang, Multi-walled carbon nanotubes added to Na2CO3/MgO composites for thermal energy storage, Particuology, Vol. 15, pp. 56-60, 2014.
[36] M. Izadi, S. F. Taghavi, S. H. N. Safavi, F. Afsharpanah, and W. Yaïci, Thermal management of shelter building walls by PCM macro-encapsulation in commercial hollow bricks, Case Studies in Thermal Engineering, Vol. 47, p. 103081, 2023.
[37] S. Li, Y. Zhou, K. Zhong, X. Zhang, and X. Jin, Thermal analysis of PCM-filled glass windows in hot summer and cold winter area, International Journal of Low-Carbon Technologies, Vol. 11, No. 2, pp. 275-282, 2016.
[38] K. A. Ismail, C. T. Salinas, and J. R. Henriquez, Comparison between PCM filled glass windows and absorbing gas filled windows, Energy and Buildings, Vol. 40, No. 5, pp. 710-719, 2008.
[39] D. Li, C. Zhang, Q. Li, C. Liu, M. Arıcı, and Y. Wu, Thermal performance evaluation of glass window combining silica aerogels and phase change materials for cold climate of China, Applied Thermal Engineering, Vol. 165, p. 114547, 2020.
[40]      K. Aliakbari, A. Ebrahimi-Moghadam, and P. Ildarabadi, Investigating the impact of a novel transparent nano-insulation in building windows on thermal comfort conditions 

  • Receive Date 04 November 2023
  • Revise Date 28 January 2024
  • Accept Date 17 February 2024

Home

Publication Ethics

Article Processing Charges

Submit Manuscript

Reviewers

Contact Us