@article { author = {Shahrouei, Zohreh and Afkar, Mohammad and Gavagsaz-Ghoachani, Roghayeh}, title = {Comparison between two controllers for a modular three level boost converter in renewable energy systems; indirect sliding mode and PI}, journal = {Journal of Renewable and New Energy}, volume = {9}, number = {2}, pages = {80-90}, year = {2022}, publisher = {Iranian Society of Heating Refrigeration Air Conditioning Engineers (IRSHRAE)}, issn = {2423-4931}, eissn = {2676-2994}, doi = {}, abstract = {Fuel cells and photovoltaic systems have many applications among renewable energy systems. DC converters play an important role in these systems. According to characteristics of renewable systems and nonlinear behaviour of the DC converters, control of them is essential. In this paper, the control of a DC modular converter is investigated. This converter is based on a three-level boost converter. This topology can increase the output voltage level compared to the input voltage level and balance the DC output voltage. There are two capacitors in each module of the converter and a capacitor is shared between two modules. The performance of the indirect sliding mode controller is compared with a classic PI controller. The system is simulated using MATLAB/ Simulink software. The simulation results are presented in several scenarios. The dynamics of the input powers and the voltage balance are studied. These tests are performed under changes in the input power, the resistance load and the input voltage. It is obvious that the proposed controller has good performance during operating point changes. The superiority of the proposed controller over the classic controller is shown for all tests. In transient mode, the linear controller is unable to balance capacitor voltages by changing the input power, input voltage and load.}, keywords = {Modular converter,PI controller,Indirect sliding mode controller,DC voltage balance,Renewable Energy System}, title_fa = {مقایسه کنترل مبدل بوست سه‌سطحی مدولار در سامانه‌های انرژی تجدیدپذیر با دو روش: کنترل‌کننده مدلغزشی غیرمستقیم و کنترل‌کننده PI}, abstract_fa = {در سامانه‌های انرژی‌های تجدیدپذیر، پیل‌های سوختی و سامانه‌های فتوولتاییک دارای کاربرد زیادی هستند. مبدل‌هایDC  علاوه بر تغییر ولتاژ نقش به‌سزایی در رفع چالش‌های این منابع به‌عهده دارند. با توجه به ویژگی‌های سامانه‌های تجدیدپذیر، کنترل این مبدل‌ها که دارای رفتار غیرخطی هستند، در عملکرد مناسب سامانه بسیار مهم است. در این مقاله، کنترل یک مبدل مدولار DC مورد بررسی قرار می‌گیرد. این مبدل بر اساس بوست سه‌سطحی بنا شده‌است. این ساختار، علاوه بر افزایش سطح ولتاژ ورودی می‌تواند تعادل ولتاژDC  را در خروجی ایجاد کند. در هر مدول این مبدل، دو خازن وجود دارد و یک خازن میان هر دو مدول مشترک است. نحوه پیاده‌سازی یک کنترل‌کننده‌ غیر خطی براساس مدلغزشی غیر مستقیم و یک کنترل‌کننده خطی سنتی PI بیان‌شده‌است. عملکرد دو کنترل‌کننده با یکدیگر مقایسه شده‌است. به‌کمک نرم‌افزار متلب/ سیمولینک، مدار شبیه‌سازی شده است. نتایج و شکل‌موج‌های ساختار مورد مطالعه ارائه داده شده است. نتایج حاصل از شبیه‌سازی، در چند بخش معرفی شده است. یک بخش شامل مقایسه دینامیک‌های توان‌های ورودی است و بخش دیگر ولتاژهای خازن‌ها جهت تعادل ولتاژ است. این بررسی‌ها برای تغییرات توان ورودی، مقدار بار و ولتاژ ورودی انجام شده است. برتری کنترل پیشنهادی نسبت به کنترل‌کننده سنتی در هر بخش نشان‌داده شده‌است. در حالت گذرا، کنترل‌کننده خطی به‌ازای تغییرات توان‌های ورودی، بار و یا ولتاژ ورودی، تعادل ولتاژ خازن‌ها را نمی‌تواند برقرار سازد.}, keywords_fa = {مبدل مدولار,کنترل‌کننده PI,کنترل‌کننده مدلغزشی غیرمستقیم,تعادل ولتاژ,سامانه‌های انرژی تجدیدپذیر}, url = {https://www.jrenew.ir/article_150486.html}, eprint = {https://www.jrenew.ir/article_150486_dcfeb55c8682f84219b92c2afbc137b1.pdf} }