ORIGINAL_ARTICLE
آنالیز اقتصادی و زیست محیطی جایگزینی سیستم گرمایشی گاز طبیعی با پمپ زمین گرمایی در منطقه ١١ تهران
با درنظر گرفتن منابع روبه اتمام سوخت های فسیلی و انتشار فراوان آلاینده های زیست محیطی از این منابع، استفاده از انرژی های پاک و تجدیدپذیر مورد توجه قرار گرفته است. یکی از این منابع انرژی تجدیدپذیر و درعین حال ساده که میتواند همزمان برای تامین گرمایش و سرمایش مورد استفاده قرار گیرد، پمپ حرارتی زمین گرمایی است. استفاده از گاز طبیعی به جز هزینه بالایی که برای دولت به دلیل یارانههای پرداختی بر روی گاز طبیعی دارد آلاینده ها و هزینههای زیست محیطی زیادی را به کشور تحمیل می کند. در این مقاله با مدل نمودن تعداد ساختمانهای در حال گرفتن پروانه ساخت در منطقه 11 شهر تهران در سال 2014 به بررسی شرایط جایگزینی پمپ حرارتی به جای سیستم های معمول توسط دولت پرداخته میشود. با توجه به نتایج حاصل شده، در صورت استفاده از پمپ های حرارتی زمین گرمایی، سالانه از انتشار بیش از 100568 تن آلاینده جلوگیری میشود و میزان کاهش هزینه های سالانه زیست محیطی ناشی از آلاینده ها 641364 دلار برآورد شده است. همچنین میتوان سالیانه میزان 12931360 متر مکعب گاز طبیعی صرفهجویی کرد که با صادرات آن، میزان 3232840 دلار سود حاصل کشور میشود. در ادامه استراتژی های حمایت دولت ایران برای ترغیب شهروندان به استفاده از این سیستم مورد بررسی قرار گرفت. مشاهده می شود که در صورت حمایت دولت از شهروندان برای استفاده از پمپهای حرارتی، بازگشت سرمایه شهروندان از 18 سال (در صورت عدم حمایت دولت) به کمتر از 2 سال خواهد رسید.
https://www.jrenew.ir/article_49049_93e501045d52610b53e54410d1e2ca0a.pdf
2016-03-20
1
6
پمپ زمین گرمایی
گاز طبیعی
آلاینده های محیط زیستی
تهران
حسین
یوسفی
hosseinyousefi@ut.ac.ir
1
استادیار، گروه انرژیهای نو و محیط زیست، دانشکده علوم و فنون نوین، دانشگاه تهران * تهران، 1439957131، Hosseinyousefi@ut.ac.ir
LEAD_AUTHOR
سهیل
رومی
2
دانشجوی کارشناسی ارشد، مهندسی سیستمهای انرژی، دانشکده علوم و فنون نوین، دانشگاه تهران
AUTHOR
ساناز
طبسی
3
دانشجوی کارشناسی ارشد، مهندسی سیستمهای انرژی، دانشکده علوم و فنون نوین، دانشگاه تهران
AUTHOR
مریم
حمله دار
4
دانشجوی کارشناسی ارشد، مهندسی سیستمهای انرژی، دانشکده علوم و فنون نوین، دانشگاه تهران
AUTHOR
[1] Iran International energy data and analysis (https://www.eia.gov/beta/international/analysis.cfm?iso=IRN)
1
[2] U.S. Energy Information Administration / Monthly Energy Review December 2015 (http://www.eia.gov/totalenergy/data/annual/#consumption)
2
[3] Iran Energy Balance Sheet, 2014
3
[4] S. Porkhial, H. Sheydae, A Performance Comparison between an Open Source and a Vertical Closed Source Heat Pump System for Residential Heating in the Cold Climate Iran, World Geothermal Congress 2015
4
[5] D. Mendrinos, C. Karytsas, Results of EU Project Ground-Med concerning Advanced Ground Source Heat Pump Systems for Heating and Cooling, World Geothermal Congress 2015
5
[6] I. Sarbu, C. Sebarchievici. General review of ground-source heat pump systems for heating and cooling of buildings. Energy and Buildings,Vol. 111, pp. 207–217, 2016
6
[7] N. Naili, M. Hazami, I. Attar, A.Farhat. Assessment of surface geothermal energy for air conditioning in northern Tunisia: Direct test and deployment of ground source heat pump system. Energy and Buildings, Vol. 111, pp. 207–217, 2016
7
[8] M. Islam , H. Mun , A. Rubayet , S. Ahmed , K. Park , C. Yang . Evaluation of a ground source geothermal heat pump to save energy and reduce CO2 and noxious gas emissions in a pig house. Energy and Buildings, Vol. 111, pp. 446–454, 2016
8
[9] P. Blum, G. Campillo, M. Munch, T. Kolbel. CO2 savings of ground source heat pump systems – a regional analysis. Renewable Energy, Vol. 35, pp. 122–127, 2010
9
[10] J. Hanova, H. Dowlatabadi, Strategic GHG reduction through the use of ground source heat pump technology, Environ. Res, No. 2, pp. 1–8, 2007
10
[11] S. Self, B. Reddy, M. Rosen. Geothermal heat pump systems: Status review and comparison with other heating options, Applied Energy, Vol. 101, pp. 341–348, 2013
11
[12] P. Conti, W. Grassi, D.Testi, Proposal of Technical Guidelines for Optimal Design of Ground-Source Heat Pump Systems, World Geothermal Congress, 2015
12
[13] L. Xin-Guo, Z. Jun, W. Jian, L. Qiang, W. Yi-Ping, J.Yan-Min, Application andExperiment on Solar-Ground Coupled Heat Pump with Heat Storage, World Geothermal Congress, 2010
13
[14] S. Porkhail, M. Taghaddosi, Renewable Energy Organization of Iran(SUNA), World Geothermal Congress, 2010
14
[15] M. Aydın, A. Sisman, A. Gultekin, B. Dehghan, An Experimental Performance Comparison between Different Shallow Ground Heat Exchangers, World Geothermal Congress, 2015
15
[16] http://www.energyhomes.org/renewabletechnology {Carey, 1998 #8}
16
ORIGINAL_ARTICLE
تاثیر کاربرد گرافن به عنوان ماده الکترودی بر بازده سلول های خورشیدی پلیمری
تولید انرژی با استفاده از پدیدهی فتوولتایی در سلولهای خورشیدی میتواند از میزان وابستگی ما به سوختهای فسیلی و تولید گازهای گلخانهای بکاهد. سلولهای خورشیدی پلیمری در مقایسه با سایر انواع سلولهای خورشیدی، اگر چه راندمان تبدیل انرژی پایین تری دارند اما دارای مزایایی چون وزن کم، انعطاف پذیری و ضریب جذب بالا هستند و فرآیندهای مربوط به تهیهی آنها نسبت به سلول های خورشیدی سیلیکونی از هزینهی کمتری برخوردار است. این دستگاه ها از سه جزء اصلی فوتوآند، لایهی فعال و کاتد تشکیل شده اند. فوتوآند اولین جزء در تماس با نور خورشید است. این لایه باید تا حد امکان شفاف باشد؛ بگونه ای که در ناحیهی مرئی فاقد جذب بوده تا بتواند بیشتر تابش فرودی را از خود عبور دهد. همچنین از هدایت الکتریکی بالا و مقاومت پایینی برخوردار باشد. فوتوآند باید دارای تابع کار بالا باشد تا بتواند حفرات تولید شده توسط لایهی فعال را بطور مطلوبی جمع آوری نماید.کاتد نیز بایستی از هدایت الکتریکی بالا و تابع کار پایین برای جمع آوری الکترون ها برخوردار باشد. در این مقالهی مروری به معرفی گرافن، خواص فیزیکی و تاثیر به کارگیری آن در راندمان سلول های خورشیدی پلیمری پرداخته شده است. همچنین مقایسهای میان بازده تولید انرژی سلولهای خورشیدی با الکترود گرافنی و سلولهای خورشیدی با الکترود معمول و متداول ایندیوم قلع اکساید (ITO)، صورت گرفته است.
https://www.jrenew.ir/article_49051_23dcd2a768123cf1837dedada5600d9e.pdf
2016-03-20
7
15
سلولهای خورشیدی پلیمری
الکترود
گرافن
زهرا
فخاران
1
دانشجوی دکترا، شیمی کاربردی، دانشگاه صنعتی امیرکبیر، تهران
AUTHOR
لیلا
ناجی
leilanaji@aut.ac.ir
2
استادیار، شیمی تجزیه (الکتروشیمی)، دانشگاه صنعتی امیرکبیر، تهران تهران، صندوق پستی 4413- 15875، leilanaji@aut.ac.ir
LEAD_AUTHOR
خسرو
معدنی پور
3
دانشیار، فیزیک، دانشگاه صنعتی امیرکبیر، تهران
AUTHOR
شعله
کاظمی فرد
4
دانشجوی دکترا، شیمی کاربردی، دانشگاه صنعتی امیرکبیر، تهران
AUTHOR
[1] N. S. Allen, Photochemistry and Photophysics of Polymeric Materials: John Wiley & Sons, 2010.
1
[2] H. Assender and A. Barkhouse, "Photovoltaic Polymer Materials," Photochemistry and Photophysics of Polymeric Materials, p. 271, 2010.
2
[3] J. Bernede, "Organic photovoltaic cells: history, principle and techniques," Journal of the Chilean Chemical Society, vol. 53, pp. 1549-1564, 2008.
3
[4] B. R. Saunders and M. L. Turner, "Nanoparticle–polymer photovoltaic cells," Advances in colloid and interface science, vol. 138, pp. 1-23, 2008.
4
[5] Y. Sun, W. Zhang, H. Chi, Y. Liu, C. L. Hou, and D. Fang, "Recent development of graphene materials applied in polymer solar cell," Renewable and Sustainable Energy Reviews, vol. 43, pp. 973-980, 2015.
5
[6] T. L. Benanti and D. Venkataraman, "Organic solar cells: An overview focusing on active layer morphology," Photosynthesis research, vol. 87, pp. 73-81, 2006.
6
[7] C.-T. Lee and C.-H. Lee, "Conversion efficiency improvement mechanisms of polymer solar cells by balance electron–hole mobility using blended P3HT: PCBM: pentacene active layer," Organic Electronics, vol. 14, pp. 2046-2050, 2013.
7
[8] L. Hu, H. S. Kim, J.-Y. Lee, P. Peumans, and Y. Cui, "Scalable coating and properties of transparent, flexible, silver nanowire electrodes," ACS nano, vol. 4, pp. 2955-2963, 2010.
8
[9] H.-Z. Geng, K. K. Kim, K. P. So, Y. S. Lee, Y. Chang, and Y. H. Lee, "Effect of acid treatment on carbon nanotube-based flexible transparent conducting films," Journal of the American Chemical Society, vol. 129, pp. 7758-7759, 2007.
9
[10] S. Bae, H. Kim, Y. Lee, X. Xu, J.-S. Park, Y. Zheng, J. Balakrishnan, T. Lei, H. R. Kim, and Y. I. Song, "Roll-to-roll production of 30-inch graphene films for transparent electrodes," Nature nanotechnology, vol. 5, pp. 574-578, 2010.
10
[11] S. Jönsson, J. Birgerson, X. Crispin, G. Greczynski, W. Osikowicz, A. D. Van Der Gon, W. R. Salaneck, and M. Fahlman, "The effects of solvents on the morphology and sheet resistance in poly (3, 4-ethylenedioxythiophene)–polystyrenesulfonic acid (PEDOT–PSS) films," Synthetic Metals, vol. 139, pp. 1-10, 2003.
11
[12] A. Manzano-Ramírez, E. J. López-Naranjo, W. Soboyejo, Y. Meas-Vong, and B. Vilquin, "A Review on the Efficiency of Graphene-Based BHJ Organic Solar Cells," Journal of Nanomaterials, vol. 2015, p. 1, 2015.
12
[13] Z. Zhuo, F. Zhang, J. Wang, J. Wang, X. Xu, Z. Xu, Y. Wang, and W. Tang, "Efficiency improvement of polymer solar cells by iodine doping," Solid-State Electronics, vol. 63, pp. 83-88, 2011.
13
[14] S. Günes, H. Neugebauer, and N. S. Sariciftci, "Conjugated polymer-based organic solar cells," Chemical Reviews, vol. 107, pp. 1324-1338, 2007.
14
[15] B. C. Thompson and J. M. Frechet, "Polymer–fullerene composite solar cells," Angewandte chemie international edition, vol. 47, pp. 58-77, 2008.
15
[16] G. Li, R. Zhu, and Y. Yang, "Polymer solar cells," Nature Photonics, vol. 6, pp. 153-161, 2012.
16
[17] W. C. Choy, Organic Solar Cells: Springer, 2013.
17
[18] R. Po, C. Carbonera, A. Bernardi, F. Tinti, and N. Camaioni, "Polymer-and carbon-based electrodes for polymer solar cells: toward low-cost, continuous fabrication over large area," Solar Energy Materials and Solar Cells, vol. 100, pp. 97-114, 2012.
18
[19] H. Kim, C. Gilmore, A. Pique, J. Horwitz, H. Mattoussi, H. Murata, Z. Kafafi, and D. Chrisey, "Electrical, optical, and structural properties of indium–tin–oxide thin films for organic light-emitting devices," Journal of Applied Physics, vol. 86, pp. 6451-6461, 1999.
19
[20] Z. Liu, S. P. Lau, and F. Yan, "Functionalized graphene and other two-dimensional materials for photovoltaic devices: device design and processing," Chemical Society Reviews, 2015.
20
[21] M. D. Irwin, D. B. Buchholz, A. W. Hains, R. P. Chang, and T. J. Marks, "p-Type semiconducting nickel oxide as an efficiency-enhancing anode interfacial layer in polymer bulk-heterojunction solar cells," Proceedings of the National Academy of Sciences, vol. 105, pp. 2783-2787, 2008.
21
[22] N. Espinosa, R. Garcia-Valverde, A. Urbina, and F. C. Krebs, "A life cycle analysis of polymer solar cell modules prepared using roll-to-roll methods under ambient conditions," Solar Energy Materials and Solar Cells, vol. 95, pp. 1293-1302, 2011.
22
[23] D. Angmo and F. C. Krebs, "Flexible ITO‐free polymer solar cells," Journal of Applied Polymer Science, vol. 129, pp. 1-14, 2013.
23
[24] X. Wang, L. Zhi, N. Tsao, Ž. Tomović, J. Li, and K. Müllen, "Transparent carbon films as electrodes in organic solar cells," Angewandte chemie, vol. 120, pp. 3032-3034, 2008.
24
[25] Y. Wang, X. Chen, Y. Zhong, F. Zhu, and K. P. Loh, "Large area, continuous, few-layered graphene as anodes in organic photovoltaic devices," Applied Physics Letters, vol. 95, p. 063302, 2009.
25
[26] Y. Xu, G. Long, L. Huang, Y. Huang, X. Wan, Y. Ma, and Y. Chen, "Polymer photovoltaic devices with transparent graphene electrodes produced by spin-casting," Carbon, vol. 48, pp. 3308-3311, 2010.
26
[27] Z. Yin, S. Sun, T. Salim, S. Wu, X. Huang, Q. He, Y. M. Lam, and H. Zhang, "Organic photovoltaic devices using highly flexible reduced graphene oxide films as transparent electrodes," ACS nano, vol. 4, pp. 5263-5268, 2010.
27
[28] L. Gomez De Arco, Y. Zhang, C. W. Schlenker, K. Ryu, M. E. Thompson, and C. Zhou, "Continuous, highly flexible, and transparent graphene films by chemical vapor deposition for organic photovoltaics," ACS nano, vol. 4, pp. 2865-2873, 2010.
28
[29] M. Choe, B. H. Lee, G. Jo, J. Park, W. Park, S. Lee, W.-K. Hong, M.-J. Seong, Y. H. Kahng, and K. Lee, "Efficient bulk-heterojunction photovoltaic cells with transparent multi-layer graphene electrodes," Organic Electronics, vol. 11, pp. 1864-1869, 2010.
29
[30] J. Geng, L. Liu, S. B. Yang, S.-C. Youn, D. W. Kim, J.-S. Lee, J.-K. Choi, and H.-T. Jung, "A simple approach for preparing transparent conductive graphene films using the controlled chemical reduction of exfoliated graphene oxide in an aqueous suspension," The Journal of Physical Chemistry C, vol. 114, pp. 14433-14440, 2010.
30
[31] Y. Wang, S. W. Tong, X. F. Xu, B. Özyilmaz, and K. P. Loh, "Interface Engineering of Layer‐by‐Layer Stacked Graphene Anodes for High‐Performance Organic Solar Cells," Advanced Materials, vol. 23, pp. 1514-1518, 2011.
31
[32] Y. U. Jung, S.-I. Na, H.-K. Kim, and S. J. Kang, "Organic photovoltaic devices with low resistance multilayer graphene transparent electrodes," Journal of Vacuum Science & Technology A, vol. 30, p. 050604, 2012.
32
[33] Y.-Y. Choi, S. J. Kang, H.-K. Kim, W. M. Choi, and S.-I. Na, "Multilayer graphene films as transparent electrodes for organic photovoltaic devices," Solar Energy Materials and Solar Cells, vol. 96, pp. 281-285, 2012.
33
[34] Z. Liu, Q. Liu, Y. Huang, Y. Ma, S. Yin, X. Zhang, W. Sun, and Y. Chen, "Organic photovoltaic devices based on a novel acceptor material: graphene," Advanced Materials, vol. 20, pp. 3924-3930, 2008.
34
[35] G. Jo, S.-I. Na, S.-H. Oh, S. Lee, T.-S. Kim, G. Wang, M. Choe, W. Park, J. Yoon, and D.-Y. Kim, "Tuning of a graphene-electrode work function to enhance the efficiency of organic bulk heterojunction photovoltaic cells with an inverted structure," Applied Physics Letters, vol. 97, p. 213301, 2010.
35
[36] Y.-Y. Lee, K.-H. Tu, C.-C. Yu, S.-S. Li, J.-Y. Hwang, C.-C. Lin, K.-H. Chen, L.-C. Chen, H.-L. Chen, and C.-W. Chen, "Top laminated graphene electrode in a semitransparent polymer solar cell by simultaneous thermal annealing/releasing method," ACS nano, vol. 5, pp. 6564-6570, 2011.
36
[37] M. Cox, A. Gorodetsky, B. Kim, K. S. Kim, Z. Jia, P. Kim, C. Nuckolls, and I. Kymissis, "Single-layer graphene cathodes for organic photovoltaics," Applied Physics Letters, vol. 98, p. 123303, 2011.
37
[38] J.-H. Huang, J.-H. Fang, C.-C. Liu, and C.-W. Chu, "Effective work function modulation of graphene/carbon nanotube composite films as transparent cathodes for organic optoelectronics," Acs Nano, vol. 5, pp. 6262-6271, 2011.
38
[39] Z. Liu, J. Li, Z.-H. Sun, G. Tai, S.-P. Lau, and F. Yan, "The application of highly doped single-layer graphene as the top electrodes of semitransparent organic solar cells," ACS nano, vol. 6, pp. 810-818, 2011.
39
[40] T. Aizawa, R. Souda, S. Otani, Y. Ishizawa, and C. Oshima, "Anomalous bond of monolayer graphite on transition-metal carbide surfaces," Physical review letters, vol. 64, p. 768, 1990.
40
[41] K. S. Novoselov, A. K. Geim, S. Morozov, D. Jiang, Y. Zhang, S. a. Dubonos, I. Grigorieva, and A. Firsov, "Electric field effect in atomically thin carbon films," science, vol. 306, pp. 666-669, 2004.
41
[42] C. Berger, Z. Song, X. Li, X. Wu, N. Brown, C. Naud, D. Mayou, T. Li, J. Hass, and A. N. Marchenkov, "Electronic confinement and coherence in patterned epitaxial graphene," Science, vol. 312, pp. 1191-1196, 2006.
42
[43] C. Zhang and T. Liu, "A review on hybridization modification of graphene and its polymer nanocomposites," Chinese Science Bulletin, vol. 57, pp. 3010-3021, 2012.
43
[44] X. Wan, Y. Huang, and Y. Chen, "Focusing on energy and optoelectronic applications: a journey for graphene and graphene oxide at large scale," Accounts of chemical research, vol. 45, pp. 598-607, 2012.
44
[45] D. R. Dreyer, R. S. Ruoff, and C. W. Bielawski, "From conception to realization: an historial account of graphene and some perspectives for its future," Angewandte Chemie International Edition, vol. 49, pp. 9336-9344, 2010.
45
[46] J. Zhu, M. Chen, Q. He, L. Shao, S. Wei, and Z. Guo, "An overview of the engineered graphene nanostructures and nanocomposites," Rsc Advances, vol. 3, pp. 22790-22824, 2013.
46
[47] Y. Zhu, S. Murali, W. Cai, X. Li, J. W. Suk, J. R. Potts, and R. S. Ruoff, "Graphene and graphene oxide: synthesis, properties, and applications," Advanced Materials, vol. 22, pp. 3906-3924, 2010.
47
ORIGINAL_ARTICLE
بررسی روشهای محاسبه نرخ نفوذ هوا به ساختمان جهت کاربرد در تهویه مطبوع و محاسبات انرژی ساختمان
به جریان هوای ورودی کنترل نشده از خارج به داخل ساختمان که از طریق شکافها و منافذ ساختمان اتفاق میافتد، نفوذ هوا میگویند. بررسی نفوذ هوا به ساختمان از چند دیدگاه همچون مصرف انرژی، طراحی سیستمهای تهویه مطبوع، آسایش حرارتی، کیفیت هوای داخل و ورود آلودگی و رطوبت اهمیت زیادی دارد. طبق تحقیقات متعددی که انجام گرفته است، نفوذ هوا 15 الی 30 درصد از بار حرارتی و مصرف انرژی ساختمان را به خود اختصاص میدهد که نشان دهنده لزوم تحقیق و شناخت بیشتر در این موضوع است. به طور کلی سه عامل فشار باد، پدیده دودکشی و سیستمهای تهویه مطبوع باعث ایجاد نفوذ هوا در ساختمان میشوند، که باید تأثیر هر سه عامل در محاسبات لحاظ شود. از دیدگاه تهویه مطبوع، مسأله اصلی، چگونگی محاسبه نرخ نفوذ هوا در ساختمان است. تاکنون چندین رابطه تحلیلی و تجربی و همچنین آزمونهای استاندارد برای محاسبه نرخ نفوذ هوا از اجزای مختلف ساختمان ارائه شدهاند. در این مقاله چند مورد از روابط و معادلات پرکاربرد ارائه شده در این زمینه بررسی شدهاند. در نهایت استفاده از معادله توانی به دلیل دقت مناسب مهندسی و کاربرد بیشتر در پژوشهای اخیر، برای محاسبه نرخ نفوذ هوا در ساختمان توصیه شدهاست.
https://www.jrenew.ir/article_49053_200ac553ba3a7992ae46134ef3a77587.pdf
2016-03-20
16
22
نفوذ هوا
منافذ ساختمان
فشار باد
هوابندی
مصرف انرژی
دانیال
حکیمی راد
danial.hakimi@modares.ac.ir
1
دانشجوی کارشناسی ارشد، مهندسی مکانیک، دانشگاه تربیت مدرس، تهران تهران، صندوق پستی: 111-14115 ، danial.hakimi@modares.ac.ir
LEAD_AUTHOR
مهدی
معرفت
2
استاد، مهندسی مکانیک، دانشگاه تربیت مدرس، تهران
AUTHOR
بهروز
محمدکاری
3
استادیار، مهندسی عمران، مرکز تحقیقات راه مسکن و شهرسازی، تهران
AUTHOR
[1] ASHRAE. Handbook of fundamentals. Chapter 16: ventilation and infiltration. USA Society of Heating, Refrigeration and Air-Conditioning Engineers, 2009.
1
[2] K. Hassouneh, A. Alshboul, and A. Al-Salaymeh, Influence of infiltration on the energy losses in residential buildings in Amman, Sustainable Cities and Society, Vol. 5, pp. 2-7, 2012.
2
[3] G. Han, J. Srebric, and E. Enache-Pommer, Different modeling strategies of infiltration rates for an office building to improve accuracy of building energy simulations, Energy and Buildings, 86, 2015, pp. 288-295.
3
[4] J. Jokisalo, et al., Building leakage, infiltration, and energy performance analyses for Finnish detached houses, Building and Environment, Vol. 44, pp. 377-387, 2009.
4
[5] C. Younes, C.A. Shdid, and G. Bitsuamlak, Air infiltration through building envelopes: A review, Journal of Building physics, Vol. 35, pp. 267-302, 2012.
5
]6[ شهریاری، غ.، بررسی تاثیر درزگیری بر بار حرارتی و برودتی مصرفی خانوار در یک منزل مسکونی نمونه، 1385.
6
]7[ نوروزی، چ.، تحلیل اثر نفوذ هوا از طریق درزهای در و پنجره به فضای اقامتی بر کیفیت هوای داخل، دانشگاه تربیت مدرس، پایان نامه کارشناسی ارشد، 1389.
7
[8] S.B. Sadineni, S. Madala, and R.F. Boehm, Passive building energy savings: A review of building envelope components, Renewable and Sustainable Energy Reviews, Vol. 15, pp. 3617-3631, 2011.
8
[9] C. Chen, et al., A methodology for predicting particle penetration factor through cracks of windows and doors for actual engineering application, Building and Environment, Vol. 47, pp. 339-348, 2012.
9
[10] T. O. Relander, J.V. Thue, and A. Gustavsen, Air tightness performance of different sealing methods for windows in wood-frame buildings, 8th Nordic Symposium on Building Physics, Copenhagen, Denmark, 2008.
10
[11] T. O. Relander, J.V. Thue, and A. Gustavsen, The influence of different sealing methods of window and door joints on the total air leakage of wood-frame buildings, Proceedings of the Nordic Symposium on Building Physics, Copenhagen, Denmark, 2008.
11
[12] A. Sfakianaki, et al., Air tightness measurements of residential houses in Athens, Greece, Building and Environment, Vol. 43, pp. 398-405, 2008
12
[13] M. I. Montoya, et al., Air leakage in Catalan dwellings: developing an airtightness model and leakage airflow predictions, Building and Environment, Vol. 45, pp. 1458-1469, 2010.
13
[14] J. Straube. Air Flow Control in Buildings, Accessed 2 September 2015; http://www.http://buildingscience.com.
14
]15[ رسولی، ه.، مطالعه عددی و تجربی نرخ نفوذ هوا از درها و پنجره های رایج داخل ایران، دانشگاه تربیت مدرس، پایان نامه کارشناسی ارشد، 1391.
15
[16] ASHRAE, Handbook of fundamentals, Chapter 27: ventilation and infiltration. USA Society of Heating, Refrigeration and Air-Conditioning Engineers, 2005.
16
[17] N. Van Den Bossche, A. Janssens, and J. Moens, Watertightness of window frames: experience of notified bodies, 4th International Building Physics Conference (IBPC), Istanbul Technical University, 2009.
17
[18] G. Finch, J. Straube, and C. Genge, Air leakage within multi-unit residential buildings–Testing and implications for building performance, Proceedings of the 12th Canadian conference on building science and technology, 2009.
18
[19] G. N. Walton, A computer algorithm for predicting infiltration and interroom airflows, ASHRAE Trans; (United States), 1984.
19
[20] T. Qi, Z. ONeill, and G.L. Augenbroe, Inverse modeling to estimate the effective leakage area in buildings, 2014.
20
[21] M. H. Sherman and W.R. Chan, Building air tightness: research and practice, Building Ventilation: the state of the Art, pp. 137-162, 2006.
21
[22] I. S. Walker, D.J. Wilson, and M.H. Sherman, A comparison of the power law to quadratic formulations for air infiltration calculations, Energy and Buildings, Vol. 27, pp. 293-299, 1998.
22
[23] ASTM E283-91, Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen, ASTM International, West Conshohocken, PA, 1999.
23
]24[ استاندارد شماره 7822 ایران، درها و دیوارهای پردهای و پنجرههای ساختمان، تعیین میزان نفوذ هوا-روش آزمون، 1382.
24
[25] M. H. Kim, J.-H. Jo, and J.-W. Jeong, Feasibility of building envelope air leakage measurement using combination of air-handler and blower door. Energy and Buildings, Vol. 62, pp. 436-441, 2013.
25
ORIGINAL_ARTICLE
افزایش عملکرد نیروگاه خورشیدی تولید بخار مستقیم فرسنل به کمک نانو ذرات
حذف سیال روغن موجود در نیروگاه های خورشیدی بدلیل مشکلات نگهداری و زیست محیطی موضوع مهمی است که در سالهای اخیر مورد مطالعه و بهرهبرداری آزمایشی قرار گرفته است. این فناوری، به تکنولوژی تولید بخار مستقیم (DSG) شهرت یافته است. در جاذب این نیروگاهها جوشش سیال مشکل ساز است که در این مقاله به کمک نانو سیال تلاش میشود که هم این مشکل کمتر گردد و هم عملکرد جاذب را بهبود بخشیم. در این مطالعه که بر پایه محاسبات عددی روابط حاکم بر انتقال حرارت و ترمودینامیک بنا نهاده شده است، پارامترهای مهم و موثر بر راندمان نیروگاهها در دو حالت سیال خالص و نانو سیال بررسی شده است. با بهره گیری از معادلات و روابط مربوط به آن ( سیال تکفاز یا دوفاز )، دما، کیفیت بخار و ضریب انتقال حرارت سیال در تمام طول لوله بررسی شده است و تاثیر مثبت نانو ذرات اضافه شده، مشاهده شد. با اضافه کردن 05/0% نانو ذرات مس، اکسید مس، نقره و اکسید تیتانیوم مشاهده شد که آب سریعتر به جوش آمده و ضریب انتقال حرارت آن حدود 5/12 درصد افزایش یافت.
https://www.jrenew.ir/article_49054_1080aedfa79f1ac34ff98fe3a770d4bf.pdf
2016-03-20
23
28
انرژیهای نو
نیروگاه خورشیدی
تولید بخار مستقیم
نانو سیال
ضریب انتقال حرارت جابجایی
علی
شهرجردی
1
مربی،مهندسی مکانیک،دانشگاه آزاد اسلامی واحد کرج،کرج
AUTHOR
رامین
مهدی پور
raminme56@gmail.com
2
استادیار، مهندسی مکانیک، دانشگاه تفرش، تفرش تفرش، 39518-79611، raminme56@gmail.com
LEAD_AUTHOR
آرش میرعبدا...
لواسانی
3
استادیار، مهندسی مکانیک، دانشگا آزاد اسلامی واحد تهران مرکز، تهران
AUTHOR
[1] L.SyamSundar, M.T.Naik, K.V.Sharma, M.K. Singh, T.Ch. Siva Reddy. Experimental investigation of forced convection heat transfer and friction factor in a tube with Fe3O4magnetic nanofluid.Experimental Thermal and Fluid Science 37, 65–71, 2012.
1
[2] G. Burgess, K. Lovegrove, S. Mackie, J. Zapata, J.D. Pye. Direct steam eneration using the SG4 500m2 Paraboloidal dish concenterator. 2011.
2
[3] J. He, Z. Qiu, L.Qiming, Y. Zhang.Optical Design of Linear Fresnel Reflector Solar Concentrators.Energy Procedia 14, 1960 – 1966, 2012.
3
[4] J.F. Feldhoff, K. Schmitz, M. Eck, L.L. Schnatbaum, D. Laing, F. Ortiz-Vives, J. Schulte-Fischedick. Comparative system analysis of direct steam generation and synthetic oil parabolic trough power plants with integrated thermal storage. Solar Energy 86, 520–530, 2012.
4
[5] G. Toghdori, S.M. Rozati, N. Memarian, M. Arvand, M.H. Bina. Nano structure black cobalt coating for solar absorber. World Renewable Energy Congress 2011.
5
[6] A. Blakers, V. Everett, M. Jelena, E. Thomsen.Thin Single Crystalline Elongate Silicon Solar Cells. Energy Procedia 15, 58 – 66, 2012.
6
[7] Zh.J. Bong, J.K. Kwang, Y. Hyungkee. Enhanced heat transfer performance of alumina sponge-like nano-porous structures through surface wettability control in nucleate pool boiling.International Journal of Heat and Mass Transfer 55, 7487–7498, 2012.
7
[8] O. Ahmed, M.S. Hamed. Experimental investigation of the effect of particle deposition on pool boiling of nanofluids.International Journal of Heat and Mass Transfer 55, 3423–3436, 2012.
8
[9] J.D.Pye. System Modelling of the Compact Linear Fresnel Reflector. A thesis presented for the degree of Doctor of Philosophy. Department of Mechanical and Manufacturing gineering Faculty of Engineering University of New South Wales. 21st May 2008.
9
[10] P.F. Incropera ,D.P. DeWitt.Fundamentals of Heat and Mass Transfer. Wiley, USA, 4 edition, 1996.
10
[11] H. Blasius, Grenzschichten in FlussigkeitenmitkleinerReibung (German), Z. Math. physics 56, 1–37, 1908.
11
[12] H John, Lienhard. A Heat Transfer Textbook. Phlogiston Press, Cambridge, Massachusetts, 3 edition, 2006.
12
[13] L. SyamSundar, M.T. Naik, K.V. Sharma, M.K. Singh, T.Ch. Siva Reddy. Experimental investigation of forced convection heat transfer and friction factor in a tube with Fe3O4magnetic nanofluid.Experimental Thermal and Fluid Science 37, 65–71, 2012.
13
[14] R.H. Notter, M.W. Rouse, A solution to the Graetz problem – III. Fully developed region heat transfer rates, Chemical Engineering Science 27, 2073–2093, 1972.
14
[15] A. Mahdy, Unsteady mixed convection boundary layer flow and heat transfer of nanofluids due to stretching sheet. Nuclear Engineering and Design 249, 248– 255, 2012.
15
ORIGINAL_ARTICLE
نگاهی بر سیستمهای خنککننده تبخیری مستقیم فعال و غیرفعال
سیستمهای خنک کننده تبخیری به دلیل مزایای چشمگیری که دارند از دیرباز مورد توجه قرار گرفتهاند. پایین بودن هزینههای اولیه جهت نصب و راهاندازی، کم بودن هزینه در طی دوره استفاده، نگهداری آسان و ارزان و تأمین هوای تازه در ساختمان از جمله مهمترین مزایای اینگونه سیستمهاست. مصرف آب نسبتاً زیاد و عدم امکان استفاده از این سیستمها در اقلیمهای مرطوب از جمله معایب سیستمهای تبخیری است. هدف از این مقاله آشنایی با اصول سرمایش تبخیری و معرفی انواع سیستمهای خنک کننده تبخیری مستقیم فعال و غیرفعال است. سیستمهای فعال (مکانیکی) هوا را از طریق یک فن بر روی پد یا غشاء خیس به جریان درمیآورند. در ادامه چندین نمونه از سیستمهای سرمایش تبخیری فعال از جمله کولر آبی، کولر اسلینگر، هواشوی و نظایر آن معرفی و نحوه عملکرد آنها مقایسه شده است. پس از آن به بررسی سیستمهای سرمایش تبخیری مستقیم غیرفعال پرداخته شده است. سیستمهای غیرفعال دارای فن نیستند و جریان هوا در آنها یا به صورت طبیعی و یا از طریق ترکیب با برخی سامانههای دیگر نظیر دودکش خورشیدی، بادگیر، دیوار تهویه شونده و ... تأمین میگردد. در این نوع سیستمها معمولاً بخش قابل توجهی از انرژی مورد نیاز، از منابع تجدیدپذیر تأمین میشود.
https://www.jrenew.ir/article_49055_61e50b2215e29ad4a186d559985d582d.pdf
2016-03-20
29
37
سرمایش تبخیری
مستقیم
فعال
غیرفعال
امیر
امیدوار
omidvar@sutech.ac.ir
1
استادیار، گروه مهندسی مکانیک و هوافضا، دانشگاه صنعتی شیراز، شیراز * شیراز، 313-71555، omidvar@sutech.ac.ir
LEAD_AUTHOR
حامد
شایانی
2
دانشجوی کارشناسی ارشد، مهندسی مکانیک، دانشگاه صنعتی شیراز، شیراز
AUTHOR
[1] Perez-Lombard, L., Ortiz, J., et al. “A review on buildings energy consumption information.” Energy and Buildings, vol. 40, 2008, pp. 394-398.
1
[2] ص. قربانی فعال، م. یاری و م. افتخاری یزدی. "بررسی امکان استفاده از کولر تبخیری میسوتسنکو در شهرهای مختلف ایران"، کنفرانس ملی علوم مهندسی، ایده های نو،تنکابن: موسسه آموزش عالی آیندگان تنکابن،1393.
2
[3] م. امیدی آوج و ا. نبی. " بررسی میزان مصرف انرژی در ساختمان و ارائه راه حلهای معماری در راستای توسعهی پایدار"، اولین کنفرانس تخصصی معماری و شهرسازی ایران، شیراز: موسسه عالی علوم و فناوری حکیم عرفی شیراز،1394.
3
[4] Çengel, Yunus A., Michael A. Boles. Thermodynamics: an engineering approach. Ed. Mehmet Kanoğlu. McGraw-Hill Education, 2015.
4
[5] Palmer, James D., CEM PE. Evaporative cooling design guidelines manual. JD Palmer, PE, CEM–United States Department of Energy,2002.
5
[6] ق. حیدری نژاد، اصول و کاربرد خنککنندههای تبخیری، انتشارات مرکز تحقیقات ساختمان و مسکن تهران،1386، چاپ اول.
6
[7] Ghiabaklou, Z. “Thermal comfort prediction for a new passive cooling system.” Building and environment ,38, 2003, pp. 883-891.
7
[8] ز. قیابکلو، مبانی فیزیک ساختمان 4: سرمایش غیرفعال، نشر جهاد دانشگاهی واحد صنعتی امیرکبیر، 1393، چاپ دوم.
8
[9] Maerefat, M., A. P. Haghighi. “Natural cooling of stand-alone houses using solar chimney and evaporative cooling cavity.” Renewable energy ,35, 2010, pp. 2040-2052.
9
[10] Ghiabaklou, Zahra. “A new Thermal wall.” International Conference on Innovations in Engineering and Technology, 2013, Bangkok (Thailand).
10
[11] Raman, P., Sanjay Mande, V. V. N. Kishore. “A passive solar system for thermal comfort conditioning of buildings in composite climates.” Solar Energy, 2001,pp. 319-329.
11
[12] م. بهادری نژاد، تهویه و سرمایش طبیعی در ساختمان، مرکز نشر دانشگاهی تهران، 1386، چاپ اول.
12
ORIGINAL_ARTICLE
تأثیر زاویه ورود هوای گرم توسط دریچههای نواری بر شرایط آسایش حرارتی و مصرف انرژی در یک تالار اجتماعات
در این تحقیق به کمک دینامیک سیالات محاسباتی به تحلیل اثرات زاویه ورود هوا از دریچههای نواری بر شرایط آسایش حرارتی و مصرف انرژی در سیستم گرمایش یک تالار اجتماعات با سیستم تهویه جابهجایی پرداخته شده است. برای این منظور دریچههای نواری ورود هوا روی دیوارهای اطراف با چهار زاویه مختلف قرار داده شده است. بر اساس نتایج به دست آمده، برای رسیدن به شرایط یکسان آسایش حرارتی برای حالتی که زاویه ورود هوا از دریچهها به ترتیب برابر 60، 45، 30، 0 قرارداده شود، دمای هوای ورودی باید به ترتیب برابر با 4/20، 6/20، 8/20، 1/21 باشد. همچنین نتایج نشان میدهد که با افزایش زاویه هوای ورودی نسبت به افق، دما و سرعت میانگین در این ناحیه حضور افراد کاهش مییابد. علاوه بر این، تخلیه افقی هوا به تالار اجتماعات موجب توزیع یکنواختتر شرایط آسایش حرارتی و مصرف انرژی بیشتر میشود. همچنین نتایج بیانگر آن است که میزان درصد کاهش مصرف انرژی نسبت به حالت تخلیه افقی برای حالتهایی که زاویه ورود هوا از دریچهها برابر 60، 45 و 30 باشد، به ترتیب برابر با 2/7%، 4/4% و 5/2% میباشد.
https://www.jrenew.ir/article_49056_707062188ffbe5ba2739cb2716ec3973.pdf
2016-03-20
38
44
فضای پرجمعیت
آسایش حرارتی
سیستم تهویه جابهجایی
مصرف انرژی
سید علیرضا
ذوالفقاری
zolfaghari@birjand.ac.ir
1
استادیار گروه مهندسی مکانیک و مدیرگروه پژوهشی انرژی در ساختمان و آسایش حرارتی دانشگاه بیرجند، بیرجند * بیرجند، صندوق پستی376/97175، zolfaghari@birjand.ac.ir
LEAD_AUTHOR
مهدی
افضلیان
2
دانشجوی کارشناسی ارشد مهندسی مکانیک، دانشگاه بیرجند، بیرجند
AUTHOR
[1] G. Kim, L. Schaefer, Tae S. Lim, J. T. Kim, Thermal comfort prediction of an underfloor air distribution system in a large indoor environment, Energy and Buildings 64(2013)323-331.
1
[2] H.B. Awbi, Ventilation of Buildings, E&FN Spon, London, 1998.
2
[3] L. Magnier, R. Zmeureanu, D. Derome, Experimental assessment of the velocity and temperature distribution in an indoor displacement ventilation jet,Building and Environment 47 (2012) 150-160.
3
[4] G. Cao, H. Awbi, R. Yao, Y.Fan, K. Sirén, R. Kosonen, J. Zhang, A review of the performance of different ventilation and airflow distribution systems in buildings, Building and Environment 73 (2014) 171-186.
4
[5] W. Sun, K.W.D. Cheong, A. K. Melikov, Subjective study of thermal acceptability of novel enhanced displacement ventilation system and implication of occupants’ personal control,Building and Environment 57 (2012) 49-57.
5
[6] W. Chakroun, K. Ghali, N. Ghaddar, Air quality in rooms conditioned by chilled ceiling and mixed displacement ventilation for energy saving,Energy and Buildings 43 (2011) 2684–2695.
6
[7] A. W. Woods, Sh. Fitzgerald, S. Livermore, A comparison of winter pre-heating requirements for natural displacement and natural mixing ventilation,Energy and Buildings 41 (2009) 1306–1312.
7
[8] B.F. Yu, Z.B. Hu, M. Liu, H.L. Yang, Q.X. Kong, Y.H. Liu, Review of research on air-conditioning systems and indoor air quality control for human health, International Journal of Refrigeration32(2009)3–2 0
8
[9] J.V.D.KOOI, A Methodology for Indoor Airflow Computations and Energy Analysis for a Displacement Ventilation System, Energy and Buildings, 14(1990)259-271.
9
[10] K.W.D. Cheong, E. Djunaedy, Y.L. Chua, K.W. Tham, S.C. Sekhar, N.H. Wong, M.B. Ullah, Thermal comfort study of an air-conditioned lecture theatre in the tropics, Building and Environment 38 (2003) 63 – 73.
10
[11] J. Lau, Q. Chen, Floor-supply displacement ventilation for workshops, Building and Environment 42 (2007) 1718–1730.
11
[12] F. Causone, F. Baldin, B. W. Olesen, S. P. Corgnati, Floor heating and cooling combined with displacement ventilation: Possibilities and limitations, Energy and Buildings 42 (2010) 2338–2352.
12
[13] H. Chen, S. Janbakhsh, U. Larsson, B. Moshfegh, Numerical investigation of ventilation performance of different air supply devices in an office environment, Building and Environment 90 (2015) 37-50
13
[14] M. H. Fathollahzadeh, G. Heidarinejad, H. Pasdarshahri, Prediction of thermal comfort, IAQ, and energy consumption in a dense occupancy environment with the under floor air distribution system, Building and Environment 90(2015) 96-104.
14
[15] Q. Chen, W. Xu, A zero-equation turbulence model for indoor airflow simulation, Energy and Buildings 28 (1998) 137-144.
15
[16] P. O. Fanger, Thermal comfort analysis and applications in environmental engineering, New York: McGraw-Hill, 1970.
16
[17] ANSI/ASHRAE, Standard 55-2010. Thermal Environmental Conditions for Human Occupancy, American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc., 2010.
17
[18] ISO7730, Moderate thermal environments—Determination of the PMV and PPD indices and specification of the conditions for thermal comfort, International Standards Organization, 1994.
18
ORIGINAL_ARTICLE
مدیریت انرژی ساختمان هوشمند با تغذیهی منابع تجدیدپذیر
امروزه روبهرویی با مشکل افزایش تقاضا با وجود زیرساخت شبکه برق کنونی قابل حل نیست. همچنین آلودگی های زیست محیطی به دلیل وجود نیروگاههای تجدیدناپذیر رو به فزونی است. بهترین راهکار به منظور کاهش تلفات در شبکه انتقال و توزیع الکتریسیته و آلودگیهای زیست محیطی ناشی از تولید آن، این است که هر ساختمان از منابع انرژی تجدیدپذیر خانگی منحصر به فرد خود که در ساختمان نصب شده تغذیه کند. این مقاله از جنبه های گوناگون همچون مدیریت انرژی در ساختمان و کنترل لوازم خانگی و انرژی الکتریکی، به بررسی یک ساختمان هوشمند با منابع انرژی تجدیدپذیر مختلف و سیستمهای ذخیرهساز انرژی پرداخته است. همچنین تاثیر استفاده از سیستم مدیریت هوشمند ساختمان با ترکیب انرژی های تجدیدپذیر را بررسی می کند. به منظور رسیدن به این شکل بار، بارها باید توسط مصرف کنندگان به درستی برنامه ریزی شود،ژ به طوری که وسایل پر مصرف در طول ساعات اوج روشن نشوند. در واقع در این مقاله از روش انتقال بار برای هموار کردن منحنی بار مصرفی استفاده میشود. یکی از اهداف این مقاله این است که در ساعات اوج مصرف برق، حداقل وابستگی به شبکه برق و حداکثر استفاده از منابع تجدید پذیر را داشته باشیم . در این مقاله یک روش جدید مدیریت انرژی با استفاده از انتقال بار یرای ساختمان های هوشمند با تغذیهی منابع تجدیدپذیر پیشنهاد میشود. با بکارگیری الگوریتم مدیریت انرژی در یک ساختمان با تغذیهی منابع تجدیدپذیر، حدود 28% در هزینهی برق ساختمان صرفهجویی میشود.
https://www.jrenew.ir/article_49058_2b2d38ac36a0be7b6d3714fc31d3b5f0.pdf
2016-03-20
45
50
مدیریت
تجدیدپذیر
تغذیه
ساختمان
هوشمند
الهام
سماواتی
e.samavati2010@yahoo.com
1
کارشناسی ارشد، مهندسی برق، دانشگاه خواجه نصیرالدین طوسی، تهران *یزد، صندوق پستی:8915161893، e.samavati2010@yahoo.com
LEAD_AUTHOR
[1] A. Mishra, D.Irwin, P.Shenoy, J.Kurose, T. Zhu, GreenCharge: Managing Renewable Energy in Smart Buildings,2013 .
1
] 2[ ساناز غازی، اعظم نادری، بررسی نقش سیستم مدیریت هوشمند(EBMS) در بهینه سازی مصرف ساختمان، صفحه 49-52، 1390.
2
[ 3] A.Radhakrishnan, M.P. Selvan, Load Scheduling For Smart Energy Management in Residential Buildings with Renewable Sources ,Hybrid Electrical Systems Laboratory,Department of Electrical and Electronics Engineering National Institute of Technology Tiruchirappalli, 2014.
3
]4[ مهدی تقی زاده ، سلمان حاجی آقاسی، ساناز اردیبهشتی ، مدیریت تقاضای مبتنی بر پیش بینی منابع تجدیدپذیر در ساختمان های مسکونی توسط سیستم خان ه های هوشمند، نخستین همایش ملی سیستم های هوشمند مدیریت ساختمان با رویکرد بهینه سازی مصرف انرژی، 1393 .
4
[5] J.Han, C.Choi, W.Park, I.Lee, S.Kim, Smart home energy management system including renewable energy based on ZigBee and PLC ,Consumer Electronics, IEEE Trans, vol. 60 ,pp. 198 - 202, 2014.
5
[6] M.Pipattanasomporn , M.Kuzlu, S.Rahman, An Algorithm for Intelligent Home Energy Management and Demand Response Analysis, IEEE TRANSACTIONS ON SMART GRID, VOL. 3, NO. 4, 2012.
6
ORIGINAL_ARTICLE
مدلسازی و تحلیل دینامیکی یک چیلر جذبی دوبستره با رویکرد استفاده از انرژی خورشیدی
در این تحقیق، رفتار دینامیکی یک چیلر جذبی که از ژلسیلیکات به عنوان جاذب و از آب به عنوان مبرد استفاده میکند، مدلسازی شده است. اثرپارامترهای مهم نظیر زمان سیکل، زمان عملکرد شیرها و زمان بازیابی حرارتی بر روی ظرفیت پمپ حرارتی و ضریب عملکرد آن تعیین و تحلیل شده و سپس مقدار بهینه آنها جهت عملکرد بهینه پمپ حرارتی محاسبه شده است. در انتها نتایج بدست آمده با نتایج تجربی مقایسه شده که تطابق بسیار خوبی را نشان میدهد. زمان سیکل 450 ثانیه که توسط سازنده استفاده میشود، بهترین مقدار برای تحصیل حداکثر خنککنندگی میباشد که البته تنها برای شرایط محیطی خاصی صادق میباشد، هر چند مقدار ضریب عملکرد با افزایش زمان سیکل، افزایش مییابد. در صورت استفاده از انرژی خورشیدی زمان سیکل متغیر بوده و بایستی بصورت برخط با توجه به شدت تابش، تعیین گردد.
https://www.jrenew.ir/article_49067_36da66fdf063a506469d8ec0d6830ce3.pdf
2016-03-20
51
56
چیلر جذبی جامد
دوبستره
تحلیل دینامیکی
استراتژی کنترل
سیلیکاژل
انرژی خورشیدی
سید عباس
سادات سکاک
sakak@eng.ikiu.ac.ir
1
استادیار، رشته مکانیک، دانشگاه بین المللی امام خمینی(ره)، قزوین قزوین، صندوق پستی 34148 - 96818، sakak@eng.ikiu.ac.ir
LEAD_AUTHOR
[1] Rowland F.S. and Molina M.J., Stratospheric sink forchlorouromethanes: Chlorine-atom catalysed destructionof ozone, Nature, 249, p. 810, 1974.
1
[2] United Nations Environment Programme. TheMontreal Protocol on Substances that Deplete the Ozone Layer. United Nations Environment Programme.
2
[3] United Nation, Report of the Conference of theParties on Its Third Session, United Nation, Kyoto 11 December 1997.
3
[4] Aristov Yu.I, Sapienza A, Ovoshchnikov D.S, Freni A, Restuuccia.G, Reallocation of adsorption anddesorption times for optimization of cooling cycles, p 525-531, 2012.
4
[5] EL- Sharkawy I.I, Abdelmeguid H, saha B.B., Towards an optimal performance of adsorptionchillers: reallocation of adsorption / desorption cycle times, p 171-182, 2013.
5
[6] Wang R.Z., Performance improvement of adsorption cooling by heat and mass recovery operation, Int. Journal of Refrigeration, 24, p. 602,2001.
6
[7] Sakoda A. and Suzuki M., Fundamental study onsolar powered adsorption coolingSystem, Journal of Chemical Engineering Japan, 17(1), p. 52, 1984.
7
[8] Glueckauf. Trans. Faraday Sci., 51, p. 1540,1995
8
[9] Cho S.H. and Kim J.N., Modeling of a silica gel/water adsorption cooling system,Energy, 17(9 ) p. 829. 1992
9
[10] H.T., Ng K.C., Chakraborty A., Oo N.M., and Othman M.A., Adsorptioncharacteristics of silica gel water systems, Journal of ChemicaL Eng. Data, 47, p.1177, 2002.
10
[11] Saha, B.B., Boelman, E.C. and Kashiwagi,T., Computer simulation of a silica gel-water Adsorption refrigeration cycle-the influence of the operation conditions on cooling output and COP, ASHRAE Tranc.Res;101(2),p.348, 1995
11
[12] Techincal Brochure from www.adsorption.de GBUmbh Adsorption
12
ORIGINAL_ARTICLE
آموزش دانشگاهی انرژیهای تجدیدپذیر
مصرف روز افزون انرژی با توجه به روند رو به رشد صنعتی شدن کشورها به همراه مشکلات زیست محیطی ناشی از این روند و همچنین نرخ بالای کاهش منابع فسیلی، همه و همه دست به دست هم داده اند تا بهره گیری از انرژی های تجدیدپذیر به عنوان راهکاری موثر مطرح گردد. تامین انرژی مورد نیاز از منابع تجدید پذیر عزمی ملی میطلبد که این مهم نیازمند فعالیتهای زیر بنایی فرهنگی از جمله آموزش در تمام سطوح جامعه میباشد. این مقاله نگاهی دارد بر فعالیتهای آموزش فنی در حوزه تجدید پذیر با بهره گیری از تجارب پنج کشور پیشرو (آلمان، چین، آمریکا، کانادا و نروژ) در این زمینه. بررسیهای انجام شده موید این مطلب است که در کنار آموزش های تئوری، جنبه های عملی آموزش بسیار حائز اهمیت میباشد. امکان استفاده از آزمایشگاهها، شرکت در دوره ها و کارگاههای تخصصی و امکان همکاری با صنعت در دورههای کارآموزی و کارورزی حرفه ای نه تنها به ارتقائ سطح علمی دانشجویان کمک کرده بلکه فرهنگ استفاده از انرژی های تجدید پذیر را در ذهن دانشجویان به یک باور انکار ناپذیر تبدیل مینماید. افراد در آینده حرفه ای خویش، نگاه ویژه ای به استفاده از این مفاهیم در طرحها، برنامهریزیها و تجربیات خود خواهند داشت. این نگاه ویژه در نسل آینده مهندسان و طراحان سر آغاز فصل نوینی از استفاده عمومی از این منبع پاک در سطح جامعه خواهد بود.
https://www.jrenew.ir/article_49068_a2d06f503c785e1a3027a967828befd4.pdf
2016-03-20
57
63
انرژی
تجدیدپذیر
آموزش
آزمایشگاه
کارآموزی
کارورزی
کبری
قرئلی و همکاران
kgharali@ut.ac.ir
1
استادیار، مهندسی مکانیک، دانشگاه تهران، تهران * تهران، 1439955961، kgharali@ut.ac.ir
LEAD_AUTHOR
آمار تفصیلی صنعت برق ایران، ویژه مدیریت راهبردی در سال 1394، شرکت مادر تخصصی توانیر، معاونت منابع انسانی و تحقیقات، پایگاه خبری صنعت برق
1
وزارت نیرو، سازمان انرژی های نو ایران (سانا) [2]
2
[3] N. Hoshangi, A.A. Allesheikh, H. Helali, Regional Assessment of Solar Radition Potentioal by Evaluation and Optimization of interpolation Methods in Iran, Journal of regional planning, 2015 , Volume 4 , Number 16
3
[4] Renewable energy sector in the EU: its Employment and Export Potential, A Final Report to DG Environment, ECOTEC Research & Consulting Limited, United Kingdom, 2002
4
[5] IRENA, REmap 2030: A Renewable Energy Roadmap, June 2014. IRENA, Abu Dhabi. www.irena.org/remap
5
[6] T. Grigoleit and, D. Lenkeit, The Renewable Energy Industry in Germany A glance at industry promotion policies in selected energy sectors, 2012 [7] B. Burger, Power Generation from Renewable Energy in Germany – Assessment of 2015, FRAUNHOFER institute for solar energy system ISE, 2016.
6
[8] I. Aigner, S. Gabriel, National Biomass Action Plan for Germany, Biomass and Sustainable Energy Supply,2009.
7
[9] Rose, A. China's solar capacity overtakes Germany in 2015, industry data show. Reuters, 2016
8
[10] Timperley, J. Chinese solar capacity outshone Germany's in 2015, Businessgreen, 2016 [http://www.businessgreen.com]
9
[11] Walker L., US Replaces China as Top Clean Energy Investor, Environmental Leader, 2012.
10
[12] J. A. Mathews and H. Tan, Economics: Manufacture renewables to build energy security, Nature, 2014
11
[13] C. Davis., Size key to success in solar panel sector,. New York (China Daily), 2013 [14] DavorH, China – hydropower as the right solution [http://www.our-energy.com/china_hydropower_as_the _right _solution.html], 2015
12
[15] Independent Statistics & Analysis, Table 1.14.A, www.eia.gov, U.S. Department of Energy Washington, DC 20585, March 2016 [16]S. Mufson, polar power project in Mojave Desert, Washington Post Staff Writer, 2010
13
[17] Independent Statistics & Analysis, Table 1.10.B, www.eia.gov, U.S. Department of Energy Washington, DC 20585, May 2016
14
[18] Renewable Energy Sources—hydropower, biomass, ethanol, biodiesel, wind, geothermal, and solar, 2014 [http://www.eia.gov/energyexplained]
15
[19] G. Bredehoeft, The Outlook for Renewable Electricity in the United States For 2014 EIA Energy Conference, Washington, DC, July 2014
16
]20[ خبرگذاری تسنیم، رشد ۷برابری تولید انرژی برق آبی در ایران نسبت به متوسط جهانی در سال 2012، شناسه خبر: 78834 سرویس: اقتصادی خرداد ۱۳۹۲
17
[21] Skelton, C. Geothermal energy could meet half of B.C.'s electricity needs, researcher says, The Vancouver Sun. [22] Obermann, E and Kutney T, OES Annual Report, CANADA, Ocean energy policy, 2014
18
[23] Oil & Gas Journal, Worldwide Look at Reserves and Production, p. 32, 2014 [24] Norway Energy Policy, Laws and Regulations Handbook Volume 1, strategic information and basic laws, IBP, Inc. - Business & Economics- 308 pages - 2015
19
ORIGINAL_ARTICLE
چرخه کرایوژنیکی جداسازی دی اکسید کربن از محصولات احتراقی نیروگاههای حرارتی
پیشبینیها حاکی از این است که دمای کره زمین تا پایان قرن بیست و یکم حدود 4/1 الی 8/5 درجه سانتیگراد افزایش مییابد. این گرمایش ناشی از تولید و انتشار گازهای گلخانهای نظیر دیاکسید کربن در جو زمین است. سهم دیاکسید کربن در میان گازهای گلخانهای در گرمایش زمین، 55% تا 67% است و بخش نیروگاهی با سهم 24% در مقایسه با سایر بخشهای صنعتی و ساختمانی، پیشتاز صنایع آلاینده میباشد. امروزه روشهای مختلف به منظور جمعآوری و ذخیرهسازی دیاکسید کربن و جلوگیری از انتشار آن در جو زمین، مطرح شدهاند. یکی از راهکارهای مطرح شده در نیروگاههای حرارتی مجاور با مخازن زیرزمینی نفت و گاز، جداسازی دی اکسید کربن از محصولات احتراقی دودکش و تزریق آن مخازن به منظور ذخیرهسازی بلند مدت در بسترهای زیرزمینی است. تزریق دیاکسید کربن به این مخازن، سبب ازدیاد برداشت علیالخصوص در بسترهای رو به اتمام خواهد شد. ، در این مقاله، چرخه کرایوژنیکی جداسازی و جمعآوری دی اکسید کربن از محصولات احتراق در نیروگاههای حرارتی معرفی میشود. در روش پیشنهادی در این مقاله، دیاکسید کربن پس از جداسازی به مخازن زیرزمینی جهت افزایش برداشت تزریق میشود. نتایج مدلسازی بیانگر این موضوع است که توان مصرفی این چرخه جداساز نسبت به توان تولیدی کل نیروگاه، حدود 2% میباشد.
https://www.jrenew.ir/article_49069_97d8ee5714d8bd4660498c8b509b5de7.pdf
2016-03-20
64
70
جداسازی دی اکسید کربن
چرخه کرایوژنیکی
نیروگاه حرارتی
محمد
امین صادقی
1
فارغ التحصیل کارشناسی ارشد مهندسی مکانیک- تبدیل انرژی، دانشگاه بین المللی امام خمینی(ره)
AUTHOR
مصطفی
مافی
m.mafi@eng.ikiu.ac.ir
2
استادیار گروه مهندسی مکانیک، دانشگاه بین المللی امام خمینی(ره) *قزوین، کدپستی 96818-34148، m.mafi@eng.ikiu.ac.ir
LEAD_AUTHOR
[1] Group III of the intergovernmental panel on climate change. IPCC special report on carbon dioxide capture and storage. Cambridge, United Kingdom: Cambridge University Press. Available from: http://www.ipcc-wg3.de/ publications/ special-reports/special report on carbon dioxide capture and storage; 2005.
1
[2] Trends in global CO2 emissions: 2015 report, www.pbl.nl/en and edgar.jrc.ec.europa.eu.
2
[3] پژوهشگاه نیرو، امکان سنجی و طراحی مفهومی بازیافت گاز دیاکسیدکربناز محصولات احتراق خروجی واحدهای نیروگاهی، شرکت برق منطقه ای تهران، کمیته مرکزی تحقیقات, 1385
3
[4] S. Burt , A. Baxter, L. Baxter, Cryogenic CO2 Capture to Control Climate Change Emissions, 34th International Technical Conference on Clean Coal and Fuel Systems, Clearwater, Florida, 2009
4
[5] G. Pipton, Power generation with CO2 capture: Technology for CO2 purification, International Journal of Greenhouse Control, Vol 3, pp528-534, 2009.
5
[6] Sebastian Posch, Markus Haider, Optimiziation of CO2 compression and purification units (CO2CPU) for CCS Power Plants, Fuel, Vol. 101, pp: 254-263, 2012.
6
[7] مصطفی مافی، توسعهی مدل مناسب خنک کاری در سیستم های جداسازی صنایع پتروشیمی و بهینه سازی ترمودینامیکی-اقتصادی آن با آنالیز ترکیبی پینچ و اکسرژی، دانشکده مهندسی مکانیک، دانشگاه صنعتی خواجه نصیر الدین طوسی، رساله دکتری، 1388.
7